I hate you so much right now. Also I think it's 5
this post was submitted on 30 Nov 2024
529 points (94.6% liked)
196
17460 readers
1090 users here now
Be sure to follow the rule before you head out.
Rule: You must post before you leave.
Other rules
Behavior rules:
- No bigotry (transphobia, racism, etc…)
- No genocide denial
- No support for authoritarian behaviour (incl. Tankies)
- No namecalling
- Accounts from lemmygrad.ml, threads.net, or hexbear.net are held to higher standards
- Other things seen as cleary bad
Posting rules:
- No AI generated content (DALL-E etc…)
- No advertisements
- No gore / violence
- Mutual aid posts require verification from the mods first
NSFW: NSFW content is permitted but it must be tagged and have content warnings. Anything that doesn't adhere to this will be removed. Content warnings should be added like: [penis], [explicit description of sex]. Non-sexualized breasts of any gender are not considered inappropriate and therefore do not need to be blurred/tagged.
If you have any questions, feel free to contact us on our matrix channel or email.
Other 196's:
founded 2 years ago
MODERATORS
It's only 5. It just overflows.
Depends on the flow from the faucet.
If it is filling 1 faster then water can move between then order will be 1->2->5
If it is slow enough then just 5 fills.
Everything else will be dry. Between 2 to 3 is sealed too. Without lids there is a lot of issues.
I think there's a potential for 4 to get wet, even though it can't fill.
load more comments
(1 replies)
load more comments
(4 replies)
Yeah nothing will fill up until 5 is full. And then since 4 has a leak it, I think basically ONLY 5 will fill.
load more comments
(12 replies)
load more comments
(2 replies)
None. The water is not running.
All the candidates are thanked for their time and asked to leave except you, who get invited to join MIB.
load more comments
(1 replies)
Looks like they’re all full of air already
load more comments
(1 replies)
5
Also, you suck.
Depends on how fast the liquid is flowing in.
Or, actually, can they even "fill"? These are 2D objects.
load more comments
(7 replies)
Unless I completely misunderstand how this works, I think 5 is the only one that will fill up. It then overflows, preventing any of the taller ones from filling. 7 is shallower but won't start filling until 3 gets fuller than 5, which it never will. This would be true whether the blockage between 2 and 3 is a mistake or not.
You are correct and I agree, but look again.
At the comments.
Then at the image.
Forget all about the water, and the question.
If necessary, reread the title.
Groan.
Please help. I have nightmares of being in a room where everyone else is just waiting patiently for me to remember the thing I forgot/figure out what is happening.
Help
load more comments
(1 replies)
By far the most annoying meme and it's not even funny.
load more comments
(2 replies)
I think you’re right. Unfortunately, we’ll still have to chalk this up as a loss.
load more comments
(1 replies)
1 fills up first. the spigot is much winder than the tube so the glass will fill faster than it can drain.
Also rule
who's to say it isn't a slow faucet?
If its not properly installed I will call a plumber to fix it.
load more comments
(1 replies)
5
Wait... Fuck!
this is right. Even if 2 to 3 is open.
The only other candidate is 1. If the faucet has much higher flow than the pipe from 1 to 2 can drain away, then 1 can fill up faster than it drains.
load more comments
(1 replies)
5, but it also depends on the circumstances. What liquid is used, temperature, viscosity, etc. There's some material science stuff that's far beyond the intended scope of this question.
load more comments
(3 replies)
I actually started to figure out the sequence...then I realized...fuck you, take my up vote
All of them are already full of air.
What if this experiment is done in space near a black hole
Is full of Hawking radiation and dreams.
OH İTS THE FUCKİNG LOSS COMİC
- 5 which begins to overflow into the room
- 7
- 4 and 6
- 2 and 3
- 1
This is assuming this is a cross section of something 3d and not something 2d otherwise air packets would get trapped and prevent some of this.
5 and 4 are the only ones getting water other than 1 and 2. 3 has a solid line blocking the flow into it, and even if that wasn't there, since 4 has a hole/drain in the bottom and 5 can overflow, 3 can't fill enough to reach the outflow. 5 is the only one that can fill up.
load more comments
(6 replies)
I'd recognise that pattern anywhere, but I focused in on the problem and almost didn't notice your dasterdly deed
load more comments
(8 replies)
Depends on how much you turn on the tap. If you fürn it up completely its 1,else its 5.
load more comments
(1 replies)
i hate you.
edit: read replies before telling me that 7 is walled off
but ignoring my loss, if everything is pressurized i think 7 if unpressurized i think 5
load more comments
(5 replies)
There's only one "one" in the diagram, so I'm gonna say the one marked "1." Pretty easy.
load more comments
(1 replies)
Wouldn't scale and viscosity play a role? Seriously, imagine a river vs a capillary tube. Also how many dimensions? And forces involved? Is that a blockage between 2 and 3? Are the walls breakable? How will the fluid hold air? Are the lines into structure 5 lower than the walls? Is this in a vacuum?
load more comments
(4 replies)
I came in to comment, "it probably would probably be 5, but I think it would depend on the flow rate?"
But reading the other comments, it looks like I'm OOTL on something? 🧐
im at a loss too
load more comments
(3 replies)
view more: next ›