vowedaloha

joined 3 years ago
[–] vowedaloha@lemmy.ca 1 points 7 months ago* (last edited 7 months ago)

You can also buy a lot of the materials from FCs. Scarce items will be scarce at FCs too, but they do pop up, just get there quickly. also, be prepared to pay a lot for these mats.

There is also mission rewards which drop a lot of rare mats, keep checking every on foot mission board for 'Procurement', but not any that go to a settlement; and, 'Salvage', Crash site or wreckage. Setup your ship with an SRV and a couple of racks of dumbfire missiles as some sites can have a welcoming party that is easiest to deal with from the air. If you do not pickup the target item, you can relog and clean out the sites again.

If you want credits, hunt down the PTN group on Discord. They have various ways to make serious credits.

Anarchy settlements can be massacred and looted with no bounties or notoriety.

[–] vowedaloha@lemmy.ca 1 points 8 months ago

Thanks to all for replying to my original request. Decided on using the finish from the above link (ENCurtis - youtube).

Not as many choices of woods around here as in large cities, I went with a cherry plywood, and the edges are a simple D shaped pine trim. After starting and making mistakes along the way, needing to sand it back down to bare wood and restarting, I got the top done. The trim pieces were a challenge as I 1) have never done any woodworking, so 2) have no tools, materials, or experience. Went through 6 different test pieces to get them finished. Since the trim is made of pine, the grain was very different than the cherry, so any finish that brought out the grain just made it look disjointed. Ended up finding Polyshades and that was what worked for me.

Next summer, will try to make a keyboard tray for this desk... Wish me luck!

[–] vowedaloha@lemmy.ca 1 points 1 year ago (2 children)

Just putting it on top. Should there be anything put between the original desk and this top?

The plan is to use some cutoffs to create a 'frame' so it cannot move (3 hidden sides) and also to then create essentially a clamp under there as well so it is reasonably stable.

This is not meant to be furniture quality, just nice and large enough for me to enjoy in my basement office and to support multiple computer monitors.

 

I'm planning on getting a hardwood plywood board to attach to an antique(ish) teachers desk so I will have a larger desk. The teachers desk is only ~2.5x4.5' and I'm looking at creating a 3x6' desktop.

My question is, with what should I finish the hardwood plywood? I want to keep/see the wood grain, and would like a finish that will be reasonably durable from day to day wear.

Thanks.

[–] vowedaloha@lemmy.ca 3 points 1 year ago (1 children)

You state "Getting certs is part of what is required for me to get bigger raises and get promoted and all that jazz." So this is not a required part of your CURRENT position. If you want a better position, you will need to invest in yourself, using some of your own time. Sounds like the employer is already paying for the courses and tests, the rest is now up to you.

Do not go in to your meeting with a bad attitude, you will just piss off your boss. Accept that if you want a promotion and higher pay that you are going to have to give up some personal time to get there. Remember, they've already given you time, and you failed, multiple times from what you wrote, so now it is time for you to hunker down and do it on your own time.

[–] vowedaloha@lemmy.ca 1 points 1 year ago

XYZZY, Plough & Y2

(From the Colossal Adventure, played on a multi million $ mainframe, when at uni. Probably in the 5-8 yrs before Doom timeframe)

[–] vowedaloha@lemmy.ca 6 points 2 years ago (1 children)

Subnautica (Do not use any hint/spoiler sites, just enjoy the evolving story) Last stop Deliver us the Moon/Deliver us Mars and to a lesser extent Quantum Break (play in story mode)

 

Is there a rep on here or does anyone have contact info for a rep?

Thanks!