casey

First time making hot sauce. I let this batch go from 09/26/2022 to 10/01/2024.

Came out amazing.

I did it very simple.

Strained peppers and garlic after removing as much Kahm yeast as I could.

Tossed all of the peppers and garlic in a blender. I added back 1/2 cup of the lacto water and 3/4 cup of white vinegar.

Didn't add anything else and it's phenomenal. It's hot but not too hot (for me). Complex flavors.

I bought several of these beer shanks back in 2015. I took it apart recently to clean.

Since the description says it's stainless steel I figured I could clean the rust off of the barb insert. Looks like it wasn't made of stainless steel.

Should I just reuse this thing or get a new one? If so I need the specs on this part so I will know what I need to buy.

Thanks for any help you can provide.

EDIT #1: Would this be a suitable replacement?

LitKiwi 2PCS Keg Coupler Barb Connector,Stainless Steel 304 Beer Kegerator Sankey Couplers,Hex Nut 5/8"G Thread x 1/4" Barb Beer Line Tailpiece Nipple Fitting with Sealing Gasket Washer https://a.co/d/g6HhP2c

EDIT #2: I emailed the customer support at MoreBeer and I got this response. They have great customer service.

Hi Casey,

Thanks for reaching out. This looks like a standard shank tailpiece. Here is a straight version, along with a curved version, in case it makes things easier.

Feel free to send me the invoice number after you order. I'm happy to refund the shipping cost for the inconvenience. Thanks!

Cheers! Zack

Zachary Marin Customer Service Representative | MoreFlavor! Inc. | 1-800-600-0033 Hours: Mon - Wed, Fri | 7:00 am PST - 4:00 pm P Visit Our Sites MoreBeer.com, MoreBeerPro.com MoreWine.com, MoreWinePro.com BrewmasterWholesale.com

cross-posted from: https://mander.xyz/post/12406051

I'm not sure where the right place to post this would be, but here goes.

I bought this DW745 Type 2 saw off of Facebook Marketplace. I think it was abused. I replaced both of the elevating shafts (5140100-04 & 5140100-05). I also had to replace both of the bevel gears (5140061-65).

The aluminum housing seems to be okay and the lifting shafts move in and out without much resistance. I'm still getting this chunky movement when I raise and lower the blade.

I'm looking for advice before I go though the whole process of replacing the entire aluminum housing on the motor.

cross-posted from: https://mander.xyz/post/12406051

I'm not sure where the right place to post this would be, but here goes.

I bought this DW745 Type 2 saw off of Facebook Marketplace. I think it was abused. I replaced both of the elevating shafts (5140100-04 & 5140100-05). I also had to replace both of the bevel gears (5140061-65).

The aluminum housing seems to be okay and the lifting shafts move in and out without much resistance. I'm still getting this chunky movement when I raise and lower the blade.

I'm looking for advice before I go though the whole process of replacing the entire aluminum housing on the motor.

I'm not sure where the right place to post this would be, but here goes.

I bought this DW745 Type 2 saw off of Facebook Marketplace. I think it was abused. I replaced both of the elevating shafts (5140100-04 Diagram # 82 & 5140100-05 Diagram # 84). I also had to replace both of the bevel gears (5140061-65 Diagram # 56).

The aluminum housing seems to be okay and the lifting shafts move in and out without much resistance. I'm still getting this chunky movement when I raise and lower the blade.

I'm looking for advice before I go though the whole process of replacing the entire aluminum housing (Gear Case A25607 Diagram # 213) on the motor.

I just got a leather strop for the first time in my sharpening journey and what a difference!

I sharpened all the straight edge knives at my in-laws before Thanksgiving Day and finished them with the strop and compound. Unreal!

I'll post links to what I used if it's allowed.