det lyder spændende med ægte kastanjer i Danmark.
Har vi da kun haft falske kastanjer indtil nu?
Scandinavian, but yeah i was mostly joking with how useless "sunup to sundown" is as a measure of time because it varies wildly by season and location.
Jeg har to kollegaer der er ramt af det her shitshow...det er helt grotesk, Semler trækker bare på skulderen og siger de fortsætter med at lede. De står begge med dæk og fælge til over 30k som bare er væk.
Well then replace pizza with whatever street/junk food is popular at your location. There's always somewhere to get it.
Ja men dengang var der også bedsteforældre til at passe...vi har to bedsteforældre i samme landsdel som os, begge har stadig fuldtidsarbejde og kan ikke bare passe børnebørn i et ubestemt antal dage eller med dags varsel.
Pasning af andre? Så skal min arbejdsgiver fandme betale meget mere i løn, vi har ikke råd til 8-10 timers babysitter flere dage i træk.
Judging from the amount of down votes, I'm guessing people are thinking KYS
Ja det er der jo desværre en risiko for. Men på den anden side nytter det heller ikke at lade det være op til arbejdsgivere at give plads til familielivet, for det magter de jo tydeligvis ikke at løfte på en passende måde af sig selv.
There's always a pizza place open somewhere within reach
Before COVID I was practically working sunup to sundown every single day of the week
That's like 5h work days 1/4 of the year...must be nice
At der overhovedet er en grænse for antal dage med barn syg er helt hul i hovedet. Der er ingen umiddelbar øvre grænse for egen sygdom, så længe vi ikke når ud i langtidssygemeldinger, det burde der heller ikke være med barn syg. Fremvisning af lægeattest ved længere sygdom end en uges tid (på arbejdsgivers regning) kan jo også bruges til barn syg hvis man er bange for svindel.
Som en der har døjet med overvægt det meste af livet (og stadig gør), så er spisning pga. kedsomhed et reelt problem for nogle mennesker. Det er helt klart en af de primære årsager til min overvægt og en virkelig svær vane at bryde.
Only been in there for a week, he's still shy but slowly becoming more brave. He explores mostly during dusk and dawn, during the day he doesn't move from this hollow cork branch but has gone from hiding at the back to peeking out the front mostly.
Picked up this little guy the other day, a male hypo bloodred het charcoal corn snake.
The little bugger has been hiding since he moved in a few days ago.
I have a cheap bedslinger, an Anycubic Kobra 2, and generally it's a pretty decent printer at the price. I have flashed klipper FW on it, so I'm not using Anycubics FW.
I have issues whenever I try printing bigger parts, the first layer is always complete shit (see post photo).
Heightmap, measured with inductive probe
range is only 0.085mm from min to max, so it should be reasonably flat. The heightmap is automatically recalibrated and loaded as part of my print_begin macro.
Slicer settings for line width
I don't know if my printer just doesn't correct Z-height during first layer, if my line width settings are completely messed up or what is causing this, but the issue is only apparent on bigger parts with large contract surface on the bed.
[SOLVED] It was just Z-offset that was too low causing this. however when running the calibration routine from ellis3dp on first layer squish, the settings that looked good on the small calibration patches, looked like crap on bigger prints. I needed a bit higher Z-offset, but that solved it.
OK det er nok fordi jeg ikke klassificerer spiselige kastanjer som "ægte" ifht. ikke-spiselige, men bare en anden type.